亚洲精品国产一区二区三区四区在线,成人福利午夜,揉少妇的双乳从后挺进视频,国产一区二区三区精彩视频,成熟放荡的肉色丝袜老,《野外激情》韩国电影

 

塑料是東莞市雙幫塑膠原料有限公司常年銷售的塑料，因為塑料價格行情每天都有新變化前天的報價不等于今天的報價。本公司銷售的所有原料保證是原廠原包,隨料可以提供生產廠商提供的物性表、SGS報告，COA原料出廠報告,UL黃卡,ROSH報告,reach報告,SVHC報告,提供原料注塑加工工程中可能出現的各種異常現象解決方法，塑料牌號太多，本網站沒有提供的本公司也有代理，詳情請咨詢本公司相關業務人員0769-87795123

 

13549213581

Technical Data

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Features and Benefits

 

• Meets ASTM D4894 Type IV, Grade 2 resin 

 

• Semi-free-flowing compression molding powder 

 

• High bulk density 

 

• Good for large billets and thin walled isostatic moldings 

 

• Very dense polymer structure, similar to non-free-flowing grades 

 

• Excellent flex life 

 

• Good dielectric strength 

 

 

Note: Data in this document are not for specification purposes.

 

 

 

 

 

 

3M™ Dyneon™

PTFE TF 1620

 

Typical Properties

 

Powder Test Method

Bulk Density ASTM D4894-98a 850 g/l

Average Particle Size ASTM D4894-98a 220 µ

 

Mechanical (measured at 23°C (73°F) on sintered moldings)

 

Tensile Strength, Minimum ASTM D4894-98a 4000 psi

Elongation at Break ASTM D4894-98a 350%

Specific Gravity ASTM D4894-98a 2.15 g/cc

Shrinkage ASTM D4894-98a 3%

Tensile Modulus ASTM D638 87,000 psi

Deformation Under Load ASTM D621

2175 psi - 24 Hours 15%

2175 psi -100 Hours 17%

2175 psi - Permanent 11%

Thermal

Flammability UL94 V-O

Melt Point (Initial) ASTM D4894-98a 342±10°C

(Second) ASTM D4894-98a 327±10°C

Service Temperature Range -200°C to 260°C (-328°F to 500°F)

Electrical

Dielectric Strength ASTM D149-95a 2.5 kV/mil

 

 

 

Processing Information

 

If transport or storage temperatures are too high the material can agglomerate in its container. In such cases, it is advisable to store the material for 48 hours at below 23°C (73°F) and then sieve it (mesh size 4 mm) (.16 in) before filling the mold. To achieve optimum properties, compression molding should be carried out within a temperature range of 23°C to 26°C (73°F to 78°F) at a pressure of 20-25 MPa (2900-5100 psi). The sintering temperature should be in the range of 375°C to 380°C (707°F to 716°F).

 

 

 

Product Form and Packaging

 

3M™ Dyneon™ PTFE TF 1620 is supplied in moisture and dust-tight plastic drums with a polyethylene liner. Quantity per drum: 50 kg (110 Ibs.)

 

Order quantity per pallet: 300 kg (660 Ibs.)

 

 

 

3

 

3M™ Dyneon™ PTFE TF 1620

 

 

 

 

 

 

 

Storage and Material Handling Safety/Toxicology

 

 

3M™ Dyneon™ PTFE TF 1620 has an unlimited shelf life provided it is stored in a clean, dry place. Dyneon PTFE TF 1620 is hydrophobic, and generally

 

does not require drying before processing unless high humidity conditions create surface moisture adsorption.

 

Management System - ISO 9001

 

and ISO 14001

 

All 3M design, development, production and service facilities have achieved a global ISO 9001 registration for their quality management system. In addition, our Gendorf, Germany location has achieved ISO 14001 for its environmental management system.

 

Regulatory

 

PTFE TF 1620 is in compliance with FDA regulation 21 CFR 177.1550. It is the responsibility of the user to

 

determine whether its specific formulation and intended use comply with applicable laws and are suilable for its intended applications.

 

 

These are fluoroplastic materials, so normal precautions observed with fluoroplastics should be followed. Before processing these products, consult the Material Safety Data Sheet and follow all label directions and handling precautions. General handling/processing precautions include: (1) Process only in well-ventilated areas;

 

(2) Do not smoke in areas contaminated with powder/ residue from these products; (3) Avoid eye contact;

 

(4) After handling these products wash any contacted skin with soap and water. Potential hazards, including evolution of toxic vapors, can exist if processing occurs under excessively high temperature conditions. Vapor extractor units should be installed above processing equipment. When cleaning processing equipment, do not bum off any of this product with an open flame or in a furnace.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warranty, Limited Remedy, and Disclaimer: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. User is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user’s method of application. Unless a different warranty is specifically stated in the applicable product literature or packaging insert, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.

 

If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.

 

Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damages arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.

 

Technical Information: Technical information, recommendations, and other statements contained in this document or provided by 3M personnel are based on tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Such information is intended for persons with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information.

 

 

 

 

 

 

 

東莞市雙幫塑膠原料有限公司大量銷售塑料注塑級PTFE 美國3M PTFE 3M™ Dyneon™ PTFE TF 1620

 

 

 

 

因為塑料價格行情每天都有新的變化前天的報價不等于今天的報價。如果需要新的價格請電：13549213581，肖生。